MyTek
Thinking Digital

Prodotti

Star InactiveStar InactiveStar InactiveStar InactiveStar Inactive
Why choose these control units:
  • Innovative and exclusive system to control opening and closing all shutters from the local controls of each window without additional buttons
  • Windows grouping and groups through simplified wiring, without software configurations, without grouping stations, without programming buttons , only 2 wires to wire the groups;
  • Ecological: consumption in Standby equal to ZERO (in Internet there are control units that consume 1 watt in standby which per year are € 2 in the bill for each blind);
  • Assistance and connection diagrams for customized systems;
  • 230Vac power supply without additional power supplies which constitute a critical point of general failure;
  • Electrical insulation, umidity and dust using two-component resin;
  • LED signaling operation;
  • 1 only type of product to make the whole system, including groups;
  • 1 only type of additional unit to control all groups from the same local window buttons;
  • Extremely compact dimensions: only 74x47x24.5mm.

Why not choose radio control units:

  • Remote control range is reduced due to a non-charged battery and / or radio interference;
  • Far windows command is not guaranteed (we think we have them closed and remain open);
  • Replace the batteries of the remote controls periodically, (it must be discovered that the farthest shutter is not controlled well, change the battery and dispose of the old one);
  • In holiday homes you can arrive after a long absence and find the batteries low;
  • Fixed costs, energy pollution and battery change, (a standby consumption of 1Wh corresponds to about 2 € / year);
  • Remote controls are subject to breakage and are much more expensive than buttons.

Why not choose the other wired controllers:

  • Grouping windows and grouping of groups (eg group plan made by groups day and night) is not planned or is difficult;
  • Complex to program;
  • Stand-by energy consumption for each blind (1Wh corresponds to about 2 € / year);
  • Sometimes there is a single auxiliary power supply which in the event of a fault locks the entire roller shutter system;
  • It is not possible to control groups from the local commands of any window;
  • The system is composed of several types of devices such as power supply, single control units, group control units, concentrators that require a preliminary study before purchase, limit modifications during construction and require more complex wiring especially if the components are distributed.

DLTAPP12 - Centralina Tapparelle

DLTAPP12

Roller shutter motor control unit

DLTAPP14 - Centralina Tapparelle con TIMEOUT motori

DLTAPP14

Roller shutter motor control unit with TIMEOUT

DLRIT12 - Centralina funzionalità aggiuntive

DLRIT12

Delay control unit for additional features

 

Easy to install products for rolling shutter and awning automation, with local, group and total control functions, without external auxiliary power supplies, without software configurations and calibration interventions. Extremely low power consumption, less than 0.01W.

pdf Download PDF documentation

pdf Download flyer in PDF

DLTAPP12 unit for shutter motor control

DLTAPP12 dimensions

 
Shutter motor control unit, two buttons up / down, grouping windows in a single command.
This unit can work individually and / or in combination with other identical units and / or with the DLRIT12 unit which allows you to control groups of windows through the same local up / down commands of each single window in the group simply extending time pressure of the buttons.
  • Up / down control, via mains voltage buttons
  • Complete ascent and descent with pressed button memory and mutual exclusion management
  • Automatic switch-off of outputs when the motor stops being absorbed and / or by simultaneous pressing up and down buttons
  • Reversal of the motion in motion passing by OFF state of the outputs
  • STOP command by pressing the UP and DOWN keys simultaneously
  • Energy saving: Standby consumption at 230Vac <0.01W
  • Robust electronics without microprocessor
  • No software parameter, dip switch or jumper to be set
  • System configuration obtained by wiring
  • Grouping windows and grouping groups up to 5 levels (Ex: 0 Local, 1 Room, 2 Zone, 3 Floor, 4 House)
  • A one-level control also acts on all lower levels
  • Reduced wiring: to group groups it is sufficient to group 1 control unit for each group
  • Group control via button and / or via DLRIT12 unit
  • LED indications to facilitate operation control
  • Power supply 230Vac max 2A
  • Input up to 7mA max
  • Mains overvoltages limitation by varistor
  • Motor overvoltage limitation and relay contacts by varistors
  • Degree of protection IP20
  • Small dimensions WxDxH 47x74x24.5mm
  • Base with perforated fins for fixing
  • Individually blister packaged or 8 unit kit
  • Instructions

ATTENTION: control unit working need that the servomechanism limit switches interrupt the current absorbed by the motor at the motion end, otherwise the control unit will continue to power the motor. Therefore, during assembly make sure that the limit switches are correctly calibrated and properly functioning. If necessary, evaluate DLTAPP14 control unit which allows you to set a TIMEOUT time for motor operation.

DLTAPP14 unit for shutter motor control with motor TIMEOUT

DLTAPP14

buy Buy DLTAPP14

DLTAPP14 is similar to DLTAPP12 control unit, but with the addition of a microprocessor to have two motor TIMEOUT timers for the UP / DOWN directions with adjustable time by trimmer between about 10 and 110 seconds.

In addition there are two other LEDs to facilitate operation control.

DLTRIT12 delay unit for controlling roller shutter units

RIT12

Delay unit, allows control group using the same up / down commands of any window in the group.
This control unit detects the pressure of a button of any window in the group and after a trimmer adjustable time in 1.5 - 6 seconds, extends the command to the whole group.
It connects in parallel to any general group buttons (which can also be omitted).
By dividing the shutters into groups is also possible to activate them in sequence, using multiple delays set at different times, thus limiting the starting peaks current and total current.
  • usable for the control of all shutters in the house from the command of every single window
  • also applicable in a second time to systems with DLTAPP12 / DLTAPP14 control units in parallel and / or in place of group commands without heavy modifications to the existing wiring
  • can be used for delayed control units departures
  • Energy saving: Standby consumption <0.01W
  • Delay adjustable by trimmer between about 1.5 and 6 seconds
  • Delay control of all the groups can be bypassed through the STOP command followed by the desired command
  • Transmission STOP command to all groups with a delay of about 0.3 seconds
  • No software parameter, dip switch or jumper to be set
  • The system configuration is obtained through wiring
  • Double terminals to save external clamps and get cleaner wiring
  • LED indications to facilitate operation control
  • 230Vac power supply
  • Degree protection IP20
  • Small dimensions WxDxH 47x74x24.5mm
  • Base with perforated fins for fixing
  • Individually blister packaged or 8 unit kit
  • Instructions

Example of connection of a single DLTAPP12 control unit

 
 

Single unit connection

Control unit connection to drive motor of a single shutter.

The diagram does not show all the safety systems that may need to be added if necessary: ​​for example overcurrent protection, differential protection, motor thermal protection, anti-crushing protection, closed-window operation and more.

Example of connection of 3 units with group control

group 3units

Control units with local controls and group control connected to the group wires without the need to go directly to a control unit.

The diagram does not show all the safety systems that may need to be added if necessary: ​​for example overcurrent protection, differential protection, motor thermal protection, anti-crushing protection, closed-window operation and more.

Example of connection of 3 units with group control

group 3units

Control units with local controls and group control connected directly to a control unit using the free terminals already present.

The diagram does not show all the safety systems that may need to be added if necessary: ​​for example overcurrent protection, differential protection, motor thermal protection, anti-crushing protection, closed-window operation and more.

Example of connection of 3 units with double control group command

group 3 CS units

The double group control is usually used to control group both from the entrance door and from the sleeping area.

The diagram does not show all the safety systems that may need to be added if necessary: ​​for example overcurrent protection, differential protection, motor thermal protection, anti-crushing protection, closed-window operation and more.

Example of connecting 3 units with control using the same Up / Down buttons

Group 3 units with DLRIT12

Control units with local controls which, if kept for more than 1.5 seconds, extend the command to the entire upper group. It is therefore not necessary to have the group command buttons that can still be added.

The diagram does not show all the safety systems that may need to be added if necessary: ​​for example overcurrent protection, differential protection, motor thermal protection, anti-crushing protection, closed-window operation and more.

Example of connection of 2 groups (living area and sleeping area) with 3 units each, with local, group and total controls

group 2 groupsS

Control units with 2 groups (living area and sleeping area) with local, group and total controls.

The diagram does not show all the safety systems that may need to be added if necessary: ​​for example overcurrent protection, differential protection, motor thermal protection, anti-crushing protection, closed-window operation and more.

Example of connection of 2 groups (living area and sleeping area) with 3 units each, with local controls that become group and total controls, extending the duration of the pressure.

floor day night delay

Control units with 2 groups (living area and sleeping area) with local controls also extended to your group, the upper groups and the total system via delay control units.

By briefly pressing a button, only the local motor is activated, keeping the command pressed for about 2 seconds, the control units of the whole group are activated and extending the command for another 2 seconds, the remaining motors are also activated. This scheme can be extended by adding other groups at the same level and / or at higher levels.

Pressing the UP and DOWN buttons simultaneously sends the STOP command to all the motors.

It is possible to activate all the motors without waiting for the expected delay, starting with a STOP command and releasing the unwanted direction.

The diagram does not show all the safety systems that may need to be added if necessary: ​​for example overcurrent protection, differential protection, motor thermal protection, anti-crushing protection, closed-window operation and more.

Example of grouping with groups and subgroups

villa structure

In the previous example there are 21 roller shutters represented with circles, the rectangles represent groups equipped with DLRIT12 units

A command to any shutter is transmitted to all the upper levels and keeping it over a certain adjustable time, DLRIT12 units are triggered which will activate all the shutters of the underlying levels, thus allowing the groups to be activated using the local buttons.

Pressing the Up and Down commands simultaneously, DLRIT12 will send the STOP signal to all lower level units.

Control units used in the scheme are all of the DLTAPP12 / DLTAPP14 type without having to add power supplies, concentrators, BUS extenders and so on.

Eventually it is possible to add one or more DLRIT12 control units to extend the functionality of group commands to the same local commands present on each single window.

Example: by adding a single DLRIT12 control unit only in the VILLA grouping, from any local control it is also possible to command the opening / closing of all the shutters of the villa simply by extending the time pressure of the button.

By adding also a DLRIT12 in the PIANO1 grouping, it is possible from the local commands of the PIANO1 to command at will the single window, the whole floor or the whole villa.

Intervention delays must be set to scale using the appropriate trimmer in the DLRIT12 control unit, reserving an increasing value for the highest grouping levels (1 ROOM, 2 AREA, 3 FLOOR, 4 VILLA).

Example ROOM 1.5 seconds
  AREA 3 seconds
  PLAN 4.5 seconds
  VILLA 6 seconds

Pressing a button in a living room window immediately starts the shutter, after 1.5 seconds the other shutters of the living room are activated, after another 1.5 seconds the kitchen and bathroom shutters of the living area are activated, after another 1 , 5 sec. all the shutters in the sleeping area and finally after another 1.5 sec. the remaining shutters of the house.

It is possible to avoid waiting for the global command VILLA by simply pressing the UP / DOWN direction simultaneously and then releasing the unwanted direction.

Unlike many home automation systems, this type of system does not have a central coordination unit which, in the event of a failure, would compromise the operation of the entire system.

Unlike home automation systems, standby consumption is limited only to protections for network discharges and in any case limited to 10mW per control unit (it takes 100 control units to make 1 watt).

This system can however be controlled by a home automation system, remote control and / or cellular, through clean contacts connected in parallel to the buttons.

info Information request Shutters

DLTAPP12 - Roller shutter automation. Ex.1

   
   

DLTAPP12 - Automation of rolling shutters with radio control. Ex.2

Star InactiveStar InactiveStar InactiveStar InactiveStar Inactive

V-TAC presenta un'elegante serie di faretti / lampade / lampioni per esterni che permettono al tuo giardino di brillare in stile quando il sole tramonta.

Scendi all'aperto con la vasta gamma di illuminazione V-TAC e decora i tuoi percorsi, pareti, pavimenti e soffitti con lampade LED a basso consumo dal design moderno e rifinito.

illuminazione giardinoS

lampade per illuminazione giardino

Caratteristiche dei prodotti
• Lampade da giardino progettate per adattarsi alle esigenze di tutti i giorni
• Disponibili in diversi modelli, formati e dimensioni
• Lampade per esterni con grado di protezione IP da IP 44 a IP 66
• Installazione facile e veloce
• Attacco per lampadine LED con attacco GU10 / E27
• Adatto per pareti, pavimento, percorsi e soffitti

Catalogo

Scarica il catalogo V-TAC nel formato PDF

User Rating: 5 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Active

AN111Antenne per ricezione canali DTT

Ampia gamma di antenne per la ricezione TV per tutte le esigenze dei clienti.

Antenne con connettore F, con filtro LTE, con 90 elementi ad alto guadagno, con plastiche bianche per meglio valorizzare l'impatto visivo.

Antenne cargo3 Antenne cargo1 Antenne cargo2
Preamplificatore a GaAsFet

User Rating: 5 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Active

BS10313S

I preamplificatori BS10312 e BS10313 a GaAsFet hanno la caratteristica di avere un alto livello di intermodulazione e una bassissima cifra di rumore.

Un amico radioamatore ci ha inviato i risultati della cifra di rumore misurata con la sua strumentazione.

I risusltati sono riportati nella tabella seguente:

N. Frequenza Cifra di rumore Guadagno
1 470 MHz 1.86 dB 17.06 dB
2 530 MHz 1.63 dB 16.51 dB
3 690 MHz 1.44 dB 17,20 dB
4 770 MHz 1.35 dB 16,64 dB
5 790 MHz 1.43 dB

16.35 dB

Star InactiveStar InactiveStar InactiveStar InactiveStar Inactive

AP18

Amplificatori per ricezione TV

 My-Tek è specializzata nella distribuzione all'ingrosso di tutti i dispositivi per la ricezione TV DTT e satellitare. Abbiamo a stock oltre 45 modelli diversi tra amplificatori da palo, centralini autoalimentati 230Vac, miscelatori standard e speciali progettati appositamente per le zone difficili dove è necessario ricevere i canali da più direzioni.

User Rating: 5 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Active

RA626Radiocomandi - Riceventi - Apriporta - Trasmettitori

Gamma completa di accessori per l'automazione che comprende: radiocomandi universali a codice fisso 433MHz a lunga portata, multifrequenza a 433, 868 e nella gamma dei 300MHz, riceventi a uno e più canali completamente configurabili con una  o più uscite a relè, apriporta di facile installazione e trasmettitori ad uno e più canali.

 

User Rating: 5 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Active

La gamma di alimentatori MyTek per alimentare gli amplificatori TV permette di accontentare anche l'installatore più esigente.

Diponiamo di vari alimentatori tra lineari e switching, con correnti in uscita che variano da 150 a 400mA.
AL1550S
- Alimentatore switching 12V 400mA
- Led verde di funzionamento
- compatto: solo 10x7x3.3cm
- connettori F
- colore bianco
 
 
 
 
 
Star InactiveStar InactiveStar InactiveStar InactiveStar Inactive

E' sufficiente la metà dei millesimi dei condòmini per installare un impianto di videosorveglianza in uno stabile.

Lo prescrive la riforma del condominio, specificando che la ripresa è consentita purché le aree video sorvegliate siano segnalate con appositi cartelli e le immagini siano conservate per un massimo di 48 ore.

My-Tek è il partner perfetto per la fornitura di telecamere CCTV, AHD e IP megapixel ad alta definizione, DVR, NVR, IBRIDI e accessori per un pratico e funzionale impianto di Videosorveglianza. Massima assistenza nella configurazione dei videoregistratori digitali.

Preleva documento nef formato PDF per tutti gli approfondimenti sul condominio e la privacy.

User Rating: 5 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Active

BS10312SMy-Tek ha una vasta gamma di preamplificatori a basso rumore (<=2dB) che permettono di aumentare il livello dei segnali DTT molto deboli (anche sotto i 45dBuV) senza alterarne la qualità. La differenza del rumore intrinseco tra un preamplificatore MyTek e qualsiasi amplificatore da palo in commercio è di circa 3dB e che sale a 7dB con amplificatori con 2 ingressi UHF oppure IV/V/UHF.

Quando i segnali non sono ricevibili in maniera soddisfacente da un'impianto terrestre, inserendo un preamplificatore subito dopo l'antenna equivale ad avere lo stesso impianto ma con un'antenna che guadagno 3dB in più o a +7dB se era collegato un amplificatori con 2 ingressi UHF.

Ne consegue che a parità di segnale, inserendo un preamplificatore anziché optare per un'antenna a guadagno più alto, si ha un notevole risparmio di denaro considerando che un'antenna a 90 elementi viene a costare dai 20 ai 40 euro in più rispetto al preamplificatore.

User Rating: 5 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Active

Gamma completa di connettori per cavi ciassiali da 5 e 6.7mm di ottima qualità e finitura in ottone.

CN1513CN1513 - Connettore F per cavo da 5mm

CN1514 - Connettore F per cavo da 6.7mm

Caratteristiche:

  • Finitura di pregio
  • Materiale utilizzato: ottone
  • Basso costo
  • Confezione da 100 Pz

User Rating: 5 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Active
Disponibili 3 nuove gamme di alimentatori per lampade a LED  12 e 24V  e con potenze fino a 350 watt.
Gli alimentatori sono protetti contro i cortocircuiti e da sovratemperatura.

ALP12060S

Alimentatore standard serie ALP

  • Tensione d'ingresso: 100 – 264Vac (170 – 264Vac per serie >= 200W)
  • Potenza max: da 15 a 350 Watt
  • Protezione: IP20
  • Alto rendimento
  • Serie StandardLine

 

Trimmer per regolazione fine della tensione d'uscita...

User Rating: 5 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Active

schema monocavoCapita spesso di dover far passare il segnale satellitare sullo stesso cavo dell'impianto terrestre, soprattutto quando si lavora su vecchi immobili a causa delle canaline di ridotte dimensioni e quando sono piene. Per questi impianto servono dei prodotti particolari che a monte riescano a miscelare il segnale satellitare con il segnale terrestre, portare i 14/18V all'LNB e i 12V stabilizzati all'amplificatore TV mentre a valle lo demiscelino.

MyTek vi mette a disposizione dei professionisti del settore diversi prodotti di qualità per poter realizzare impianti monocavo.

Star InactiveStar InactiveStar InactiveStar InactiveStar Inactive
DVR IBRIDIDisponibili i videoregistratori My-Tek di alta qualità a 4 / 8 / 16 ingressi compatibili con telecamere IP, Analogiche e AHD.
Il software, windows like, è completo di tutte le funzioni principali e avanzate. I DVR sono già preconfigurati e pronti all'uso.
I DVR IBRIDI possono visualizzare 3 categorie di telecamere:
- IP da 1 Megapixel e 2 Megapixel con risoluzione di ben 1920x1080px
- Analogiche con risoluzione di ben 960H
- AHD con risoluzione di 1280x720px e le nuovissime da 1920x1080px.
Star InactiveStar InactiveStar InactiveStar InactiveStar Inactive

Nuova gamma ILLUMINAZIONE LED

LED lampsGamma completa di lampadine / faretti / plafoniere / strisce e accessori per l'illuminazione a prezzo molto competitivi.

Scopri i vari prodotti come: Lampade LED, Fari LED, Strisce LED, Accessori LED

Star InactiveStar InactiveStar InactiveStar InactiveStar Inactive

DIxSsPartitori per segnali TV e SAT a 2 / 3 / 4 uscite.

- CC passante con diodi su tutte le uscite.

- Frequenza di lavoro: 5-2500MHz

- Dimensioni ridotte con connettori F rivolti nella stessa direzione per minimizzare lo spazio occupato

- Schermatura totale compatibili con segnali LTE

Star InactiveStar InactiveStar InactiveStar InactiveStar Inactive

Star InactiveStar InactiveStar InactiveStar InactiveStar Inactive

RA649 è la ricevente di cui tutti gli specialisti di Automazione hanno bisogno per i loro impianti. Presenta 2 contatti puliti con uscite pilotate da 2 relè completamente indipendenti tra loro, programmabile in tutte le sue funzioni dall'installatore, multifrequenza e alimentabile sia in corrente continua che alternata.

Può apprendere fino a circa 60 codici differenti che possono essere estesi a 1000 con una memoria supplementare da inserire nello zoccolo interno.

Tramite il pulsante e i 2 LED presenti, la ricevente può essere programmata nelle varie funzioni:

  • Apprendere uno o più codici per l'attivazione delle due uscite;
  • Rimozione di uno o più codici dalla memoria precedentemente memorizzati;
  • Impostare la frequenza di funzionamento tra: 433.92 - 868.3 - 315* - 288*  - 300* - 303* - 306* - 310* - 318*  - 330* - 390* - 403.55* - 418* - 433.42 - 434.15 - 434.42 - 868.5 - 868.8 MHz (* frequenze che non possono essere utilizzate in EUROPA);
  • Settare il tipo di uscita (le due uscite possono essere programmate anche in modo diverso tra loro in quanto completamente indipendenti) tra: uomo presente, bistabile, bistabile ON/OFF, timer 500ms - 1s - 15s - 30s -  1m - 2m - 5m - 10m - 15m - 30m - 45m - 60m;
  • Funzionamento predefinito delle uscite: uscita normalmente aperta, normalmente chiusa, elettroserratura e poi apri, motore avanti e indietro;
Star InactiveStar InactiveStar InactiveStar InactiveStar Inactive
VR3404C - VR3408C
VR3404P, VR3408P, VR3416P
VTA101,VTA102,VTA103
VTA104, VTA105
VTA101C,VTA102C,VTA103C
VTA104C,VTA105C,1920x1080px

User Rating: 5 / 5

Star ActiveStar ActiveStar ActiveStar ActiveStar Active

Per tutti i nostri clienti un bel GILET multitasca imbottito invernale

 

GIL00Gilet invernale, con cerniera centrale coperta da patta e automatici, collo imbottito alla coreana, 3 taschini applicati al petto a soffietto chiusi con alette e velcro, 2 tasche interne chiuse con cerniera e 2 tasche applicate a soffietto chiuse con alette e velcro, elastico interno al giromanica.

CE: I^ categoria per rischi minimi

 

Star InactiveStar InactiveStar InactiveStar InactiveStar Inactive
TelecamereDisponibili a magazzino una vasta scelta di telecamere di alta qualità per videosorveglianza con infrarossi per la visione notturna.

In particolare la serie IPC sono delle telecamere IP con definizione di 2 MPX (1920x1080px), la serie VTAxxx delle AHD con definizione di 1280x720px, la serie VTAxxxC da 1920x1080px ed infine la serie VTxxx la serie analogica usata in abbinamento a impianti citofonici e rimodulazione.

 Abbiamo inoltre delle microtelecamere e delle telecamere Speed Dome IP e AHD con definizione di 1920x1080px.

Log in Register

Login to your account

Username *
Password *
Remember Me

INGROSSO

Ricezione TV

Radiocomandi

Videosorveglianza

Illuminazione LED

Registrati per la scontistica

NEW PRODUCTS

×

TOP